03539905
Form P7109
Edition 2
March, 1999
OPERATION AND MAINTENANCE MANUAL
FOR MODEL 1712B2/VW–1035
IMPACT WRENCH
Ingersoll–Rand is not responsible for customer modification of tools for applications on
which Ingersoll–Rand was not consulted.
IMPORTANT SAFETY INFORMATION ENCLOSED.
READ THIS MANUAL BEFORE OPERATING TOOL.
IT IS THE RESPONSIBILITY OF THE EMPLOYER TO PLACE THE INFORMATION
IN THIS MANUAL INTO THE HANDS OF THE OPERATOR.
FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY.
•
•
•
Always wear hearing protection when operating
this tool.
Keep hands, loose clothing and long hair away from
rotating end of tool.
PLACING TOOL IN SERVICE
•
•
•
Always operate, inspect and maintain this tool in
accordance with American National Standards
Institute Safety Code for Portable Air Tools
(ANSI B186.1).
Note the position of the reversing lever before
operating the tool so as to be aware of the direction
of rotation when operating the throttle.
Anticipate and be alert for sudden changes in
motion during start up and operation of any power
tool.
Keep body stance balanced and firm. Do not
overreach when operating this tool. High reaction
torques can occur at or below the recommended air
pressure.
For safety, top performance, and maximum
durability of parts, operate this tool at 90 psig (6.2
bar/620 kPa) maximum air pressure at the inlet
with 3/4” (19 mm) inside diameter air supply hose.
Always turn off the air supply and disconnect the
air supply hose before installing, removing or
adjusting any accessory on this tool, or before
performing any maintenance on this tool.
Do not use damaged, frayed or deteriorated air
hoses and fittings.
•
•
•
•
Tool shaft may continue to rotate briefly after
throttle is released.
•
•
Air powered tools can vibrate in use. Vibration,
repetitive motions or uncomfortable positions may
be harmful to your hands and arms. Stop using any
tool if discomfort, tingling feeling or pain occurs.
Seek medical advice before resuming use.
Use accessories recommended by Ingersoll–Rand.
Use only impact sockets and accessories. Do not use
hand (chrome) sockets or accessories.
Impact wrenches are not torque wrenches.
Connections requiring specific torque must be
checked with a torque meter after fitting with an
impact wrench.
Be sure all hoses and fittings are the correct size
and are tightly secured. See Dwg. TPD905–1 for a
typical piping arrangement.
•
Always use clean, dry air at 90 psig maximum air
pressure. Dust, corrosive fumes and/or excessive
moisture can ruin the motor of an air tool.
Do not lubricate tools with flammable or volatile
liquids such as kerosene, diesel or jet fuel.
Do not remove any labels. Replace any damaged
label.
•
•
•
•
•
USING THE TOOL
•
•
This tool is not designed for working in explosive
atmospheres.
This tool is not insulated against electric shock.
•
Always wear eye protection when operating or
performing maintenance on this tool.
The use of other than genuine Ingersoll–Rand replacement parts may result in safety hazards, decreased tool
performance, and increased maintenance, and may invalidate all warranties.
Repairs should be made only by authorized trained personnel. Consult your nearest Ingersoll–Rand Authorized
Servicenter.
Refer All Communications to the Nearest
Ingersoll–Rand Office or Distributor.
Ingersoll–Rand Company 1999
Printed in U.S.A.
MAINTENANCE SECTION
(Dwg. TPA1387)
PART NUMBER FOR ORDERING
PART NUMBER FOR ORDERING
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Motor Housing . . . . . . . . . . . . . . VW–1036
Back Cap . . . . . . . . . . . . . . . . . . VW–1037
Seal . . . . . . . . . . . . . . . . . . . . . . . 588–216
Plug (2) . . . . . . . . . . . . . . . . . . . . R2–227
Clamp Washer . . . . . . . . . . . . . . 2934–207
Rear End Plate . . . . . . . . . . . . . . 2934–12
Rear Rotor Bearing . . . . . . . . . . 508–97
Rotor . . . . . . . . . . . . . . . . . . . . . VW–1043
Vane Packet (set of 6) . . . . . . . . . 2934–42–6
Cylinder . . . . . . . . . . . . . . . . . . . VW–1042
Front End Plate . . . . . . . . . . . . . . 2934–11
Front Rotor Bearing . . . . . . . . . . 810–97
Cylinder Dowel . . . . . . . . . . . . . 2934–98
Air Port Gasket (2) . . . . . . . . . . . R44H–210A
15 Gasket Support (2) . . . . . . . . . . . 2940–200
16 Hammer Case Assembly . . . . . . VW–1065
17
*
Hammer Case Bushing . . . . . 2934–641
Hammer Case Label . . . . . . . WARNING–2–99
18 Hammer Case Gasket . . . . . . . . . 2934–36
19 Hammer Case Cap Screw (4) . . . 834–638
20 Hammer Case Lock Washer (4) . 34U–58
21 Back Cap Cap Screw (4) . . . . . . P225–146
22 Back Cap Lock Washer (4) . . . . VSM–1453
23 Hammer Frame Assembly . . . . . 2934–704
24
Hammer Pin (2) . . . . . . . . . . 2934–704
25 Hammer . . . . . . . . . . . . . . . . . . . 1712–724
26 1” Square Drive Anvil . . . . . . . . 1712–726
*
Not illustrated.
3
MAINTENANCE SECTION
Disassembly of Impact Mechanism
1. Remove the Anvil by rotating it as it is lifted out of
the Hammer Frame Assembly (23)..
2. Lift the Hammer Frame Assembly off the rotor shaft.
3. Push the two Hammer Pins (24) out of the Hammer
Frame and slide the Hammer (25) out of the Frame.
Always wear eye protection when operating or perform-
ing maintenance on this tool.
Always turn off the air supply and disconnect the air
supply hose before installing, removing or adjusting any
accessory on this tool, or before performing any mainte-
nance on this tool.
Disassembly of the Motor
1. Lightly clamp the Motor Housing in leather–covered
or copper–covered vise jaws with the Back Cap (2)
upward.
2. Using a hex wrench, unscrew and remove the Cap
Screws (21) and Lock Washers (22).
LUBRICATION
Each time a Series 1712B2/VW–1035 Impactool is disas-
sembled for maintenance and repair or replacement of
parts, lubricate the tool as follows:
3. Lift the Back Cap off the Housing. Remove the Seal
(3) from the inside of the Back Cap.
1. Work approximately 10 cc of Ingersoll–Rand No. 100
Grease into the impact mechanism. Coat the Anvil
(26) lightly with grease. Also coat the inside of the
Hammer Case Bushing (17) with grease.
2. Use Ingersoll–Rand No. 50 Oil for lubricating the
motor. Inject approximately 3 cc of oil into the air
inlet before attaching the air hose.
4. Remove the Clamp Washer (5) from the Housing.
5. Remove the assembled motor from the vise jaws and
using a plastic hammer, tap the splined shaft of the
Rotor (8) to dislodge the Rotor from the Front Rotor
Bearing (12).
6. Lift the Motor Housing off the Rotor, Rear End Plate
(6) and Rear Rotor Bearing (7). The Rear End Plate
and Rear Rotor Bearing will remain together as a
unit.
7. Remove the Vanes (9) from the Rotor.
8. Pull the Rear End Plate off the Rotor.
9. Open a set of vise jaws wide enough to clear the hub
of the Rear End Plate and sharply rap the hub end of
the End Plate on the top of the jaws to dislodge the
Rear Rotor Bearing.
10. Remove the Cylinder Dowel (13) and lay the Motor
Housing on top of the vise jaws with the Front Rotor
Bearing (12) downward between the jaws. Using a
soft drift pin, tap the Bearing out of the Housing.
11. To remove the Cylinder (10) and Front End Plate
(11), thread four 1/4”–20 thread socket head cap
screws that are at least 3” (75 mm) long into the Back
Cap end of the Housing. Grasping the Housing with
the installed screws downward, sharply strike the
heads of the screws on a sturdy table to dislodge the
Cylinder. The Cylinder should drop out of the Hous-
ing after a few impacts. If it does not, proceed as fol-
lows:
DISASSEMBLY
General Instructions
1. Do not disassemble the tool any further than neces-
sary to replace or repair damaged parts.
2. Whenever grasping a tool or part in a vise, always use
leather–covered or copper–covered vise jaws to pro-
tect the surface of the part and help prevent distor-
tion. This is particularly true of threaded members
and housings.
3. Do not remove any part which is a press fit in or on a
subassembly unless the removal of that part is neces-
sary for repair or replacement.
4. Do not disassemble the tool unless you have a com-
plete set of new gaskets and O–rings for replacement.
Disassembly of the Tool
1. Grasp the tool in leather–covered or copper–covered
vise jaws with the square drive upward.
2. Using a hex wrench, unscrew and remove the four
Hammer Case Cap Screws (19), and Hammer Case
Cap Screw Lock Washers (20).
3. While lightly tapping the end of the Anvil (26) with a
plastic hammer, lift off the Hammer Case
Assembly (16).
The following procedure requires the use of heat.
Take all precautions necessary to prevent being
burned.
4. Remove the Hammer Case Gasket (18).
4
MAINTENANCE SECTION
a. Carefully heat alternate sides of the Housing until
it is very warm.
b. Using thick, heavy gloves to avoid being
burned, grasp the Housing and repeat the attempt
to dislodge the Cylinder.
Excessive clamping pressure will distort the Motor
Housing and make motor installation extremely
difficult. Do not insert the hammer case end of the
Motor Housing more than 1” (25 mm) into the vise
jaws.
12. Remove the two Air Port Gaskets (14) and Gasket
supports (15) from the Housing.
8. Lightly clamp the Motor Housing in leather–covered
or copper–covered vise jaws with the motor bore
upward.
9. Lubricate and install a new fiber Gasket Support
(15) into each of the air ports inside the Motor Hous-
ing.
ASSEMBLY
General Instructions
1. Always press on the inner ring of a ball–type bearing
when installing the bearing on a shaft.
2. Always press on the outer ring of a ball–type bearing
when pressing the bearing into a bearing recess.
3. Whenever grasping a tool or part in a vise, always use
leather–covered or copper–covered vise jaws. Take
extra care with threaded members and housings.
4. Always clean every part and wipe every part with a
thin film of oil before installation.
10. Install an Air Port Gasket (14) into each opening
against the Retainer with the flat end of the Gasket
away from the Retainer.
11. Using an assembly rod that is approximately 3/16”
diameter x 8” long (5 mm diameter x 203 mm long),
insert the rod through cylinder dowel holes in the End
Plates and Cylinder to align the components. Allow
the rod to protrude through the Front End Plate far
enough to enter the dowel hole in the bottom of the
motor bore.
5. Apply a film of O–ring lubricant to all O–rings before
final assembly.
Assembly of the Motor
12. Insert the rod into the motor housing dowel hole and
slide the assembled motor along the rod into the Mo-
tor Housing. The assembly will be at the proper depth
when the Rear End Plate is slightly below the face of
the Motor Housing. Remove the assembly rod and
insert the Cylinder Dowel (13) into the assembly.
13. Place the Motor Clamp Washer (5), concave side
first, over the hub of the Rear End Plate so that the
outer rim of the Washer contacts the End Plate.
14. Install the Seal (3) on the inside of the Back Cap.
15. Install Back Cap on Housing and secure with Cap
Screws (21) and Lock Washers (22). Tighten to
5–7 ft–lb (6.8–9.5 Nm) torque.
1. Press the Front Rotor Bearing (12) into the
recess at the hammer case end of the Motor Housing
(1).
2. Slide the Front End Plate (11), bronze face first, over
the spline hub of the Rotor (8).
3. Stand the assembled Rotor and End Plate upright,
grasping the rotor spline with leather–covered or
copper–covered vise jaws.
4. Place a Vane (9) in each slot in the Rotor.
5. Slide the Cylinder (10) down over the Rotor, aligning
the holes in the Cylinder with those in the Front End
Plate.
6. Using a sleeve that will contact only the outer ring of
the Rear Rotor Bearing (7), press the Bearing into the
Rear End Plate (6).
7. Using a sleeve that will contact only the inner ring of
the Rear Rotor Bearing, press the assembled Bearing
and End Plate onto the short hub of the Rotor.
16. If Plugs (4) were removed or are being replaced,
apply pipe thread sealant and tighten to 10–20 ft–lb
(13.5–27 Nm) torque.
5
MAINTENANCE SECTION
Assembly of the Impact Mechanism
Assembly of the Tool
1.
2.
3.
Coat the Hammer (25) with Ingersoll–Rand No. 100
Grease.
1.
2.
Place the Hammer Case Assembly (16) over the
mechanism assembly against the Gasket. Make
certain the Hammer Case Label is at the top of the
tool.
Install the Hammer Case Cap Screws (19) and Lock
Washers (20) and using an alternating pattern,
tighten the Cap Screws to 20–25 ft–lb (27–34 Nm)
torque.
Position the Hammer inside the Hammer Frame (23)
and install the two Hammer Pins (24).
Install the Anvil (26) through the Frame and
Hammer until it bottoms on the lower part of the
Frame.
Set the assembled hammer mechanism onto the rotor
shaft spline.
Place the Hammer Case Gasket (18) over the
mechanism against the face of the Motor Housing.
Grease the Anvil and top of the Hammer Frame with
Ingersoll–Rand No. 100 Grease.
4.
5.
6.
TROUBLESHOOTING GUIDE
Trouble
Probable Cause
Solution
Replace complete set of Vanes.
Worn or broken Cylinder and/or Examine Cylinder and replace it if it is worn or
Low power
Worn or broken Vanes
scored End Plates
broken or if bore is scored or wavy. Replace End
Plates if they are scored.
Dirty motor parts
Disassemble tool and clean all parts with a
suitable cleaning solution. Assemble the tool and
inject 3 cc of recommended oil into Inlet and run
tool to lubricate internal parts.
Motor will not run
Tool will not impact
Incorrect assembly of motor
Disassemble motor and replace worn or broken
parts and reassemble as instructed.
Insufficient lubricant in the
impact mechanism
Broken or worn impact
mechanism parts
Remove Hammer Case Assembly and lubricate
impact mechanism.
Remove Hammer Case and examine impact
mechanism parts. Replace any worn or broken
parts.
Impact mechanism not assembled Refer to Assembly of the Impact Mechanism.
correctly
SAVE THESE INSTRUCTIONS. DO NOT DESTROY.
6
7
|