InFocus Projector Accessories SP CEIL 010 User Manual

Hardware description  
The Digital Projector Mount utilizes the following hardware. Note that the letters associated with the hardware  
on this list correspond to the letters listed in the instructions for each installation method.  
A. Four (4) 6 (mm) x 10 (mm) Phillips head screws (supplied)  
27700B S.W. Parkway Ave.  
Wilsonville, Oregon 97070-9215  
1-800-294-6400  
B. One (1) mounting bracket (supplied)  
SP-CEIL-010 DIGITAL PROJECTOR MOUNT  
I
nstallation Instructions  
These are the installation instructions for your Digital Projector Mount. Included are four methods of  
installation.  
Select the method that works best for your viewing situation. The methods are:  
C. Digital Projector (not included)  
D. One (1) Litemount Plus® assembly (supplied)  
°
Fixed Height Ceiling Installationbest for short ceilings, eight (8’) or lower  
°
°
Adjustable Height Ceiling Installationbest for high ceilings, nine (9’) feet or higher  
SP-LTMT-EXTP-S height adjustable extension is required.  
°
Wall Mount Installationfor installing the Digital Projector Mount on a rear wall the  
SP-LTMT-EXTP-S height adjustable extension is required.  
NOTE: If the required height range is greater than 12½", the optional SP-LTMT-EXTP could be used to  
extend the length of the suspension adapter. For further information or ordering assistance, please contact us  
at the phone number and address listed at the top of this column.  
Before You Start the Installation  
The wall or ceiling where you want to install the digital projector must be capable of supporting a weight that is  
five (5) times the weight of 7lbs the projector you are installing. Consult the projector’s documentation for  
weight specifications. If the wall, ceiling, tabletop, shelf, or floor is not strong enough to handle five (5) times  
the weight of 7lbs, then you must reinforce the installation environment. If you are unsure about the  
installation environment, please consider having it reinforced and having the projector installed by qualified  
personnel. Failure to do so could result in serious personal injury and damage to the projector.  
NOTE: Hardware item (E) is what secures the Digital Projector Mount to your ceiling, wall, tabletop, floor.  
Make sure you consult with your local hardware store staff for the type of hardware that works best for your  
installation environment.  
E. SINGLE WOOD STUD: If mounting on a single wood stud use three (3) #14 x 2" Lag bolts (minimum)  
commercially available. Use the mounting points on the center of the plate as indicated in the assembly  
diagram.  
° SOLID STRUCTURE: If mounting to a solid structure use four (4) 5/16" x 2" Lag bolts or commercially  
available hardware (depending on the installation requirements). Use the mounting points found on the outer  
points of the mounting plate as indicated in the assembly diagram.  
To avoid personal injury, use only an approved projector mount. Using an unauthorized projector mount may  
lead to poor ventilation and projector failure.  
When installing the projector mount, keep in mind that the projector’s focus ring is not squarely in the center  
of the front of the projector, but offset by several inches. Make sure that when you mount the projector you  
offset the installation to match the amount of inches that the projector’s focus ring is offset from the center of  
the front of the projector.  
F. Allen wrench (supplied)  
R
LISTED  
E176225  
Copyright by InFocus Corporation  
Wilsonville, OR. All rights reserved  
1
 
Wood stud  
E
Ceiling structure  
Center of wood stud  
Ceiling plate  
Remove (M8)  
Hex head screws, flat  
washers and star  
lock washers  
D
Remove the center  
extension from the  
assembly  
Insert and rotate 180°  
and lock down  
B
C
Remove (M8)  
Hex head screws, flat  
washers and star  
lock washers  
A
Solid ceiling structure  
E
Replace the ceiling  
plate  
D
Bottom assembly  
C
B
Insert and rotate 180°  
and lock down  
Replace (M8)  
Hex head screws, flat  
washers and star  
lock washers  
C
A
3
 
Wood stud  
E
Ceiling structure  
Center of wood stud  
Adjustable Height Ceiling Installation  
Complete the following steps to install the projector mount and projector on your ceiling with the optional  
suspension adapter.  
D
Adjustable screws  
This installation works best with high ceilings (FIGURE 3).  
Extension adapter  
Note: Look at the bottom of the upper assembly (D) and locate the arrow. Make sure you install the projector  
mount with the arrow pointing toward your screen.  
C
6.  
7.  
Use the Allen wrench (F) to remove the upper plate from the mount assembly (D).  
Use the Allen wrench to remove the two screws from the enclosed end of the of the suspension  
adapter, and place it into the slotted extension on the upper plate (E). Make sure that the two (2) outer  
holes on the suspension adapter align with the holes on the slotted extension on the upper plate.  
8.  
9.  
Replace the two screws removed in step 2 into the two (2) holes to secure the suspension adapter to  
the upper plate.  
Attach the mount assembly to the suspension adapter and secure them with the two screws removed  
in step 1.  
Insert and rotate 180°  
and lock down  
B
10. Secure the upper assembly to the ceiling using the commercially available hardware (E) suitable for  
your environment. Be sure that the upper assembly arrow is pointing toward your screen.  
11. Carefully raise the projector (C) with the mounting bracket (B) attached and insert it into the bottom of  
the upper assembly (D) by its tabs.  
12. Rotate the projector (C) with the mounting bracket (B) attached 180º so that the projector’s focus ring  
is pointing toward your screen.  
C
A
13. Align the safety knob on the mount assembly with the end of the arrow-shaped slot on the mounting  
Solid ceiling structure  
bracket (B) and screw it through the opening to prevent further rotation. Hand-tighten the safety knob.  
D
14. Hand-tighten the remaining two tension knobs to secure the mounting bracket to the amount  
SEE FIGURE  
3
CAUTION: Check all of the hardware for proper tightness and security. Do not over-tighten the screws.  
NOTE: Use the Allen wrench key (F) for the following modification  
E
Adjustable screws  
Extension adapter  
C
WARNING  
When using the optional  
extension adapters and making  
a height adjustment while  
secured to the wall or ceiling do  
not remove the screws  
completely from the extension.  
Failure to do so could result in  
injury and damage to the  
projector.  
Insert and rotate 180°  
and lock down  
B
C
A
4
 
Wall Mount Installation  
Complete the following steps to install the projector mount and projector to your wall. (FIGURE 4)  
Wall wood stud  
Wall structure  
Note: Look at the bottom of the upper assembly (D) and locate the arrow. Make sure you install the projector  
mount with the arrow pointing toward your screen.  
D
NOTE: Follow step 3 to secure the extension to the mount assembly.  
15. Secure the upper plate to the wall using the commercially available hardware (E) suitable for your  
environment. Be sure that the screen indicator arrow is pointing toward your screen.  
Adjustable extension  
16. Carefully raise the projector (C) with the mounting bracket (B) attached and insert it into the bottom of  
the mount assembly by its tabs.  
17. Rotate the projector (C) with the mounting bracket (B) attached 180º so that the projector’s focus rings  
is pointing toward your screen.  
E
18. Align the safety knob on the mount assembly with the end of the arrow-shaped slot on the mounting  
bracket (B) and screw it through the opening to prevent further rotation. Hand-tighten the securing  
knob.  
Adjustable screws  
19. Hand-tighten the remaining two tension knobs to secure the mounting bracket (B) to the mount  
assembly (D).  
B
CAUTION: Check all of the hardware for proper tightness and security. Do not over-tighten the screws.  
SEE FIGURE  
4
WARNING  
NOTE: Use the Allen wrench key (F) for the following modification  
When using the optional  
extension adapters and making  
a height adjustment while  
secured to the wall or ceiling do  
not remove the screws  
C
completely from the extension.  
Failure to do so could result in  
injury and damage to the  
projector.  
B
A
C
5
 

Ingersoll Rand Heat Pump LM2203A XX C4 User Manual
Insignia Indoor Furnishings NS 3IN1MT50C User Manual
JAMO Speaker System P404HG User Manual
JL Audio Speaker 10W6V2 D4 User Manual
John Lewis Freezer JLFFW1807 User Manual
JVC Car Stereo System GET0199 001A User Manual
JVC Portable CD Player RC BZ5LB User Manual
JVC Stereo System CA DXU8 User Manual
Kenmore Microwave Oven 72164682 User Manual
KitchenAid Ventilation Hood 9760425A User Manual